HYDRAULIC CHUCKS
Catalog Number
Min Clamping Length E
Max RPM
Weight (lbs.)
Fig.
Ød
ØD
ØD 1
ØD 2
L
L 1
L 2
2.9 3.1 2.6 2.9 3.1 2.9 2.9 3.5 3.1 3.8 3.1 3.8 3.1 4.0 9.3
BBT40-HDC3S-90 BBT40-HDC3S-135 BBT40-HDC4S-60 BBT40-HDC4S-90 BBT40-HDC4S-135 BBT40-HDC5S-90 BBT40-HDC6S-110 BBT40-HDC6S-150 BBT40-HDC8S-110 BBT40-HDC8S-150 BBT40-HDC10S-110 BBT40-HDC10S-150 BBT40-HDC12S-110 BBT40-HDC12S-150 BBT50-HDC4S-150 BBT50-HDC4S-200 BBT50-HDC6S-150 BBT50-HDC6S-200 BBT50-HDC8S-150 BBT50-HDC8S-200 BBT50-HDC10S-150 BBT50-HDC10S-200 BBT50-HDC12S-150 BBT50-HDC12S-200
1.50 1.73
.94
3.54 5.31 2.36 3.54 5.31 3.54 4.33 5.91 4.33 5.91 4.33 5.91 4.33 5.91 5.91 7.87 5.91 7.87 5.91 7.87 5.91 7.87 5.91 7.87
1.73 2.24
— 84 —
35,000 30,000 30,000 30,000 30,000 30,000 30,000 28,000 30,000 28,000 30,000 25,000 30,000 25,000 20000 15,000 20,000 15,000 20,000 15,000 20,000 15,000 20,000 15,000
3mm
.551
.63
1.02
1
.75 .94
.87
4mm
.551
1.50
1.77 2.24 1.81 2.36 2.24 2.36 2.05 2.36 2.05 2.36 2.05
3.31 3.31
.75
1.02
2
5mm
.551
1.50 1.50 1.89 1.57 1.97 1.65 1.97 1.73 1.97 2.05 2.20 2.05 2.20 2.12 2.28 2.20 2.36 2.28 2.44
.94
— —
.83
1.06 1.02 1.18 1.10 1.26 1.18 1.34 1.26
1 2 1 2 1 2 1 2
6mm
.551
.98
3.35
—
8mm
.669
1.18
3.35
—
10mm
.748
1.26
3.35
—
12mm
.827
1.38
3.35 3.27 3.94 3.27 3.94 3.27 3.94 3.27 3.94 3.27 3.94
4mm
.551
1.02
2.24
.75
10.1
9.3
6mm
.551
1.02
.98
10.1
2.24
9.5
2
8mm
.669
1.10
1.18
10.4
9.5
10mm
.748
1.18
1.26
10.6
2.05
9.7
12mm
.827
1.26
1.38
10.6
• Adjusting screw cannot be used • Some coolant may leak from the inner diameter slits when center through coolant is used with models marked
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
GRIP BAR PG. 397
133
Powered by FlippingBook