HYDRAULIC CHUCKS
SUPER SLIM TYPE CLAMPING RANGE: Ø3-12mm For Drills, Reamers, Ball Mills, End Mills, Diamond Reamers & Grinding Tools
COOLANT
THROUGH
H Max
H Max
Coolant Pipe (Optional)
Coolant Pipe (Optional)
Min Clamping Length E
Min Clamping Length E
L 1
L 1
Manual Clamping Hole
Manual Clamping Hole
L
L 2
L
Fig. 2
Fig. 1
Catalog Number
H Max
Max RPM
Weight (lbs.)
Fig.
Ød
ØD
ØD 1
ØD 2
L
L 1
L 2
E
4mm 6mm 8mm
HSK-A40-HDC4S-65 HSK-A40-HDC6S-75 HSK-A40-HDC8S-75 HSK-A40-HDC10S-75 HSK-A40-HDC12S-80 HSK-A50-HDC4S-75 HSK-A63-HDC3S-90* HSK-A63-HDC3S-120* HSK-A63-HDC4S-75 HSK-A63-HDC4S-90 HSK-A63-HDC4S-120 HSK-A63-HDC5S-120 HSK-A63-HDC6S-120 HSK-A63-HDC6S-150 HSK-A63-HDC8S-120 HSK-A63-HDC8S-150 HSK-A63-HDC10S-120 HSK-A63-HDC10S-150 HSK-A63-HDC12S-120 HSK-A63-HDC12S-150 HSK-A100-HDC4S-150 HSK-A100-HDC6S-150 HSK-A100-HDC8S-150 HSK-A100-HDC10S-150 HSK-A100-HDC12S-150
.83 .91
2.559
1.10 1.54
.75 .98
42,000 40,000
.73 .75 .79 .82 .88 1.8 2.4 1.1 2.2 2.2 2.4 2.4 2.4 2.9 2.7 2.9 2.7 3.1 2.7 3.1 5.6 5.6 6.2 6.2 6.4
.551
1.93
1.30
—
.669 .748 .827 .551
1.02 1.10 1.22
1.22 1.30 1.42
2.95
1
1.57
38,000
1.85
10mm 12mm
3.15
1.77 1.22 1.69 2.24 1.02 1.69
35,000 35,000 30,000 30,000 30,000 30,000 30,000 30,000 30,000 28,000 30,000 28,000 30,000 25,000 30,000 25,000 20,000 20,000 20,000 20,000 20,000
4mm
1 1 2
1.57
.83 .83
2.953 3.543 4.016 2.953 3.543
— 2.17 — 2.68
.75 .63 .63
3mm
1.02
2.83
3.86
.79 .91
— 2.09 — 2.68
1
4mm
.75
.551
2.83
5mm
.87
4.724
2.24
3.86
1.02
2.76 3.35 2.76 3.35 2.76 3.43 2.76 3.43
6mm
1.89
.98
5.910 4.724 5.910 4.724 5.910 4.724 5.910
5.04 3.74 4.92 3.70 4.88 3.66 4.84
2
8mm
.669
1.10
1.22
2.05
10mm
.748
1.18
1.30
12mm
.827
1.26
1.42
4mm 6mm 8mm
.75 .98
.551
2.05
1.02
2.25
4.76
5.910
3.54
2
.669 .748 .827
2.13 2.20 2.28
1.10 1.18 1.26
1.22 1.30 1.42
2.05
10mm 12mm
4.53
*Some coolant comes out from the inner slots in coolant-through application
• Coolant pipe must be ordered separately • Adjusting screws cannot be used
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
GRIP BAR PG. 397
194
Powered by FlippingBook