BIG DAISHOWA High Performance Tooling Solutions Vol 2

CHAMFER MILLS

C-CUTTER MINI INSERTS

SE (SHARP EDGE) TYPE Sharp edge prevents burrs. Recommended for stainless steel & mild steel.

45º

ØD

Fig. 1

Fig. 2

Fig. 3

INSERT CLASSIFICATIONS

ACP200/ACP300

CWS20A

ACM250F

DS20

NF15KA

For all steel & stainless steel materials Multi-layer PVD coating on carbide base with nanoscale TiAIN & AICrN. Excellent performance and wear resistance.

For hardened steel

For stainless steel

For aluminum & / non-ferrous materials

For cast iron

Significantly improved toughness while maintaining hardness. Uses a tough carbide base material. AlTiSiN abrasion resistance due to the super multi-layered thin film structure of the system. Excellent PVD coated carbide.

PVD-coated carbide with excellent smoothness and resistance to welding and chipping, due to the ultra-multilayered thin film structure made of AITiN and TiAICrN

DLC coating on carbide base with very smooth surface for a low coefficient of friction. Excellent performance against built-up edge.

Adopts K15-equivalent carbide material with hardness & toughness for cast iron.

Insert Grade

Insert Model

Nose Radius

Insert Clamping Screw Set

Fig.

ØD

ACP200

ACP300

CWS20A ACM250F

DS20

NF15KA

CM0302 CM0402 CM0502

1 1

.130 .156

.008 .008

— —

S1.6S-T3 S2SS-T6

—

S2TS-T6

.197

.008

CM0502SE

—

CM10C1

— —

.394

.008

S4S-T15

CM10C1SE

—

• Inserts are available in packages of 10 pcs. • Please clarify the insert model and grade when ordering (ex: CM0402(ACP300)) • 10 screws and 1 wrench are included with insert clamping screw set • It is recommended to regularly replace clamping screws and wrench to ensure the correct clamping force is maintained • SE in the Insert Model means Sharp Edge Type

STANDARD CUTTING CONDITIONS C-CUTTER MINI CUTTING DATA

Feed (IPT)

Cutting Speed (SFM)

Material

Insert Grade

Coolant

Chamfering Face Milling

Stainless Steel, Carbon Steel, Alloy Steel

ACP200, ACP300

330-1150 330-655 265-525 165-260 330-825 130-195 65-100 330-1155 330-2640

.002-.016 .002-.016 .002-.016 .002-.016 .003-.012 .001-.003 .001-.003 .004-.020 .004-.020

.002-.008 .002-.008 .002-.008 .002-.008 .003-.008 .001-.003 .001-.003 .002-.010 .002-.012

Dry Dry Dry Dry

Alloy Tool Steel

Pre-hardened Steel, Hardened steel <HRC50

CWS20A

Hardened Steel HRC50-62

Stainless Steel

Dry/Wet

Titanium

ACM250F

Wet Wet Dry

Inconel

Cast Iron

NF15KA

Aluminum/Non-Ferrous

DS20, ACP300

Dry/Wet

• This table is a guideline for selecting cutting parameters; adjust them as needed according to the machine and workpiece conditions. • Generally, wet cutting effectively improves finishing surfaces • Wet cutting effectively suppresses built-up edges occurring on stainless steel or aluminum chamfering • For aluminum/non-ferrous materials marked with DS20 is the No.1 recommendation; if chatter occurs with DS20, use ACP300

CUTTING CONDITIONS FOR SPOT FACING HOLE TYPE AND LONG TYPE OF BOLT HOLE & TAP STARTING HOLE TYPE

Cutting Speed (SFM)

Material

Insert Grade

Feed (IPT)

Coolant

Unalloyed Steel, Carbon Steel, Alloy Steel

ACP200 ACP300

66-330 165-525 99-330

.001-.005 .002-.008 .001-.005

Wet Dry Wet

Cast Iron

NF15KA

Aluminum/Non-ferrous

ACP200, ACP300

• This table is a guideline for selecting cutting parameters. Adjust them as needed according to the machine and workpiece conditions • Short projection length types other than the LONG TYPE are recommended for stainless steel and pre-hardened steel

609