HYDRAULIC CHUCKS
Catalog Number
Min Clamping Length E
Adjusting Screw
Weight (lbs.)
Fig.
ød
øD øD 1
L
L 1
L 2
H
BBT40-HDC6-60
.75
—
2.7 3.0 3.3 3.6 4.2 2.7 3.0 3.3 3.8 4.3 2.7 3.0 3.3 3.8 4.3 2.7 3.0 3.4 3.9 4.3 3.0 3.4 3.9 2.9 3.1 3.5 4.1 5.1 3.2 3.5 4.1 3.1 3.8 4.3 5.2
1
1.063
2.36 3.54 4.33 5.31 6.50 2.36 3.54 4.33 5.31 6.50 2.36 3.54 4.33 5.31 6.50 2.36 3.54 4.33 5.31 6.50 3.54 4.33 5.31 2.95 3.54 4.33 5.31 6.50 3.54 4.33 5.31 3.54 4.33 5.31 6.50
-90
1.97 2.76 3.74 4.69
-110 -135 -165
6mm
1.10-1.97
1.10
HDA6-05032
1.77
2
1.024
1.73
-HDC8-60
1
1.142
.75
—
-90
1.97 2.76 3.74 4.69
8mm
-110 -135 -165
1.77
1.10-1.97
1.10
HDA8-06032
2
1.102
1.73
-HDC10-60
1
1.220
.79
—
-90
1.97 2.76 3.74 4.69
10mm
-110 -135 -165
1.77
1.30-2.17
1.30
HDA10-08032
2
1.181
1.77
-HDC12-60
1
1.299
.79
—
-90
1.93 2.72 3.70 4.69 1.93 2.72 3.70 1.42 1.93 2.72 3.70 4.69 1.93 2.72 3.70 1.97 2.76 3.74 4.69
12mm
-110 -135 -165
1.77
1.50-2.36
1.50
HDA12-10032
2
1.260
1.77
-HDC14-90
-110 -135
14mm
1.50
HDA12-10032
2
1.339 1.77
1.81
1.50-2.36
-HDC16-75
1.38
-90
1.77
16mm
-110 -135 -165
2
1.496
1.70-2.76
1.70
HDA16-16037
1.85
1.97
-HDC18-90
-110 -135
18mm
1.70
HDA16-12037
2
1.575 1.77
1.89
1.70-2.76
-HDC20-90
1.77
-110 -135 -165
20mm
1.89
1.70-2.76
1.70
HDA16-12037
2
1.654
1.97
• In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with HYDRAULIC CHUCKS. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
PERFECT SEAL/ JET COLLET PG. 361
129
Powered by FlippingBook