HYDRAULIC CHUCK
Catalog Number
Min Clamping Length E
Adjusting Screw
Max RPM
Weight (lbs.)
Fig.
ød
øD øD 1
L
L 1
H
3.35 1.57
2.36
—
2.6 3.1 3.7 2.9 3.3 4.2 2.9 3.5 4.4 2.9 3.5 4.4 4.6 5.3 6.0 7.3 8.2 5.3 5.7 6.4 5.3 5.7 6.6 5.5 6.0 6.8 5.5 6.0 6.8 5.7 6.6 7.3 6.0 6.8 7.9 7.3 8.2
HSK-A63-HDC14-85
-120 -150
4.72 5.90 3.54 4.72 5.90 3.54 4.72 5.90 3.54 4.72 5.90
14mm
1.50
15,000
1.340
1.77 1.50-2.28
HDA12-10025
2.56
—
-HDC16-90
-120 -150
16mm
1.500
1.81
2.28-2.68 1.69-2.68
HDA16-12015 HDA16-12037 HDA16-12037 HDA20-16015 HDA25-16039
2
1.97
2.56
-HDC18-90
-120 -150
18mm
1.570
1.81
2.28-3.68 1.69-2.68
1.69
13,000
2.56
—
-HDC20-90
-120 -150
20mm
1.650
1.89
2.28-2.68 1.69-2.68
HDA20-16015 HDA25-16039
25mm 32mm
2.170 2.48 2.360 2.95
4.72 2.01 4.92 2.32
3.74 3.94
2.05 2.20 1.69 2.05 2.20
-HDC25-120 -HDC32-125
3
—
12,000
HSK-A100-HDC.750-4
.750
2 3 3
1.654 2.480 2.717
— 4.00 2.00 1.69-2.76 — 4.00 3.54 2.05-3.15 — 4.50 3.58 2.20-3.15
HDA16-12037 13,000 HDA25-16039 13,000 HDA25-16039 12,000
-HDC1.000-4 -HDC1.250-4.5
1.000 1.250
1.81
—
2.95 1.02
-HDC6-75
-120 -165
6mm
4.72 6.50
17,000
1.020
1.73 1.10-1.89
HDA6-05032
1.10
2.95 1.02
1.81
—
-HDC8-75
-120 -165
8mm
1.100
4.72 6.50
1.73 1.10-1.89
HDA8-06032
15,000
3.54 1.65
2.40
—
-HDC10-90
-120 -165
10mm
1.188
4.72 6.50 3.74 4.72 6.50 3.94 5.31 6.50 4.13 5.31 6.50
1.30
1.77 1.30-2.09
HDA10-08032
1.97
2.48
—
-HDC12-95
4
-120 -165
12mm
1.260
1.85
1.50
HDA12-10025 HDA12-10032
1.50-2.28
2.68
—
-HDC16-100
-135 -165
16mm
1.500
2.09
HDA16-12030 HDA16-12037
1.69-2.68
13,000
1.69
2.87
—
-HDC20-105
-135 -165
20mm
1.650
2.32
2.28-2.68 1.69-2.68
HDA20-16015 HDA25-16039
25mm 32mm
2.240 2.48 2.520 2.95
2.05 2.20
-HDC25-110 -HDC32-110
4.33 2.44
3.07
—
12,000
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with HYDRAULIC CHUCKS. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
• Coolant pipe must be ordered separately • “H” indicates the adjustment length with an adjusting screw • “H” dimension is the Max tool shank length that can be inserted into the holder • Do not attempt to balance before first consulting BIG KAISER • In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides (ex: HDA6-05020W)
• Adjusting screws cannot be used with models marked • Straight collet cannot be used with models marked
ACCESSORIES
PERFECT SEAL/ JET COLLET PG. 361
187
Powered by FlippingBook