CHAMFER MILLS
C-CENTERING CUTTER A multifunction cutter capable of both spot drilling and chamfering.
COOLANT
THROUGH
Hole Chamfering
Hole Chamfering
Hole Chamfering
Centering & Chamfering
Centering & Chamfering
Centering & Chamfering
Chamfering
Chamfering
Chamfering
Reaming
Reaming
Reaming
Tapping
Tapping
Tapping
Drilling
Drilling
Drilling
End Milling
End Milling
End Milling
L
L 1
H Min
Back Spot Facing
Back Spot Facing
Back Spot Facing
Tap Hole Chamfering
Tap Hole Chamfering
Tap Hole Chamfering
Back Chamfering Face Milling Back Chamfering Face Milling Back Chamfering Face Milling
Chamfering
Chamfering
Chamfering
Chamfering
Chamfering
Chamfering
H
Catalog Number
ØC Min .079 .079 .079
ØC Max .354 .512 .787
H Min .024 .024 .012
ØD
ØD 1
ØD
L
L 1
Insert
ST8-CN0209-45-65 ST12-CN0213-45-90 ST20-CN0220-45-110
8mm .393 12mm .551 20mm .866
2.56 3.54 4.33
.590 .787
CN0406 CN0606 CN0906
H = D/2 - 0.7 mm
1.181
• Wrench and screw is included; inserts must be ordered separately • As the insert has a nose radius, spot drilled tip is not acute • Use with hand feed is not recommended Chamfering Back Chamfering Chamfering Back Chamfering Chamfering Back Chamfering
Chamfering
Chamfering
Chamfering
Chamfering
Chamfering
Chamfering
INSERTS FOR C-CENTERING CUTTER
Centering & Chamfering
Centering & Chamfering
Centering & Chamfering
Plunge Milling
Plunge Milling
Plunge Milling
Shoulder Milling
Shoulder Milling
Shoulder Milling
Helical Milling
Helical Milling
Helical Milling
Ramping
Ramping
Ramping
Insert Grade
DS20 (For Aluminum) Peck Drilling Peck Drilling Peck Drilling
Helical Milling
Helical Milling
Helical Milling
Shoulder Milling
Shoulder Milling
ØD Shoulder Milling
Catalog Number
Screw Set Catalog Number
Slotting
Slotting
Slotting
Ramping
Ramping
Ramping
ACM250F (For Steel/Cast Iron/Stainless Steel)
ACZ150 (For Steel/Cast Iron/Stainless Steel)
CN0406 CN0606 CN0906
.187 .250 .375
S2TS-6IP S2.5S-8IP S4S-15IP
l
l
l
l
l
l
l
l
l
• Inserts are available in a packet of 10 pcs.; please specify the insert model number and grade when ordering Example: CN0906 ACM250F.........10 Pcs • The insert clamping screw set contains 10 screws and 1 wrench • Insert clamping screws and tightening wrench are consumables; order periodically for replacement or spares.
RECOMMENDED CUTTING CONDITION
• The table is just a reference to determine cutting conditions, it should be adjusted according to the condition of the machine tool and workpiece • Be sure to use water-soluble cutting fluid during spot drilling • For traverse chamfering, dry cutting (including air blowing) is recommended; however, if severe built-up edge occurs in aluminum machining, use water-soluble cutting fluid
Feed (IPT) Spot Drilling Traverse Chamfering
Cutting Speed Vc (SFM)
Workpiece Material
Carbon Steel, Alloy Steel
165-500 165-400 230-650 330-1000
.001-.003 .001-.002
Stainless Steel
.002-.008
Cast Iron
.001-.003
Aluminium, Non-ferrous Metals
617
Powered by FlippingBook