HYDRAULIC CHUCKS
Catalog Number
Min Clamping Length E
Adjusting Screw
Weight (lbs.)
Fig.
ød
øD øD 1
L
L 1
L 2
H
BBT40-HDC7-90 BBT40-HDC8-60 BBT40-HDC8-90 BBT40-HDC8-110 BBT40-HDC8-135 BBT40-HDC8-165 BBT40-HDC9-90 BBT40-HDC10-60 BBT40-HDC10-90 BBT40-HDC10-110 BBT40-HDC10-135 BBT40-HDC10-165 BBT40-HDC11-90 BBT40-HDC12-60 BBT40-HDC12-90 BBT40-HDC12-110 BBT40-HDC12-135 BBT40-HDC12-165 BBT40-HDC13-90 BBT40-HDC14-90 BBT40-HDC14-110 BBT40-HDC14-135 BBT40-HDC15-90 BBT40-HDC16-75 BBT40-HDC16-90 BBT40-HDC16-110 BBT40-HDC16-135 BBT40-HDC16-165 BBT40-HDC18-90 BBT40-HDC18-110 BBT40-HDC18-135 BBT40-HDC20-90 BBT40-HDC20-110 BBT40-HDC20-135 BBT40-HDC20-165
2 1
7mm 1.063 1.77
3.54 2.36 3.54 4.33 5.31 6.50 3.54 2.36 3.54 4.33 5.31 6.50 3.54 2.36 3.54 4.33 5.31 6.50 3.54 3.54 4.33 5.31 3.54 2.95 3.54 4.33 5.31 6.50 3.54 4.33 5.31 3.54 4.33 5.31 6.50
1.73
1.97
1.10-1.97
1.10
HDA6-05032
2.9 2.7 3.0 3.3 3.8 4.3 3.1 2.7 3.0 3.3 3.8 4.3 3.1 2.7 3.0 3.4 3.9 4.3 3.1 3.0 3.4 3.9 3.1 2.9 3.1 3.5 4.1 5.1 3.2 3.5 4.1 3.1 3.8 4.3 5.2
1.142
.75
—
1.97 2.76 3.74 4.69 1.97
8mm
1.77
1.10-1.97
1.10
HDA8-06032
2
1.102
1.73
2 1
9mm 1.142 1.77
1.77
1.10-1.97
1.10
HDA8-06032
1.220
.79
—
1.97 2.76 3.74 4.69 1.97
10mm
1.77
1.30-2.17
1.30
HDA10-08032
2
1.181
1.77
2 1
11mm 1.220 1.77
1.77
1.30-2.17
1.30
HDA10-08032
1.299
.79
—
1.93 2.72 3.70 4.69 1.93 1.93 2.72 3.70 1.93 1.42 1.93 2.72 3.70 4.69 1.93 2.72 3.70 1.97 2.76 3.74 4.69
12mm
1.77
1.50-2.36
1.50
HDA12-10032
2
1.260
1.77
2
13mm 1.299 1.77
1.85
1.50-2.36
1.50
HDA12-10032
2
14mm 1.339 1.77
1.81
1.50-2.36
1.50
HDA12-10032
2
15mm 1.457 1.77
1.85 1.38
1.69-2.76
1.69
HDA16-12037
1.77
2
16mm 1.496
1.70-2.76
1.70
HDA16-16037
1.85
1.97
2
18mm 1.575 1.77
1.89
1.70-2.76
1.70
HDA16-12037
1.77
2
20mm 1.654
1.89
1.70-2.76
1.70
HDA16-12037
1.97
• In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”.
ACCESSORIES
PERFECT SEAL/ JET COLLET PG. 404
GRIP BAR PG. 415
SCREW PG. 415
141
Powered by FlippingBook