HYDRAULIC CHUCKS
HYDRAULIC CHUCK (JET COOLANT TYPE) CLAMPING RANGE: ø4-32mm Coolant Holes Through Body of Holder
COOLANT
Jet Through
THROUGH
H
H
Coolant Pipe (Optional)
Coolant Pipe (Optional)
E
E
Manual Clamping Hole
Manual Clamping Hole
L 1
L 1
L
L
Fig. 1
Fig. 2
Catalog Number
Min Clamping Length E
Weight (lbs.)
Fig.
ød
øD
øD 1
øD 2
L
L 1
H
HSK-A63-HDC4J-75 HSK-A63-HDC4J-120 HSK-A63-HDC6J-90 HSK-A63-HDC6J-120 HSK-A63-HDC6J-165 HSK-A63-HDC8J-90 HSK-A63-HDC8J-120 HSK-A63-HDC8J-165 HSK-A63-HDC10J-90 HSK-A63-HDC10J-120 HSK-A63-HDC10J-165 HSK-A63-HDC12J-90 HSK-A63-HDC12J-120 HSK-A63-HDC12J-165 HSK-A63-HDC16J-120 HSK-A63-HDC20J-120 HSK-A63-HDC25J-120 HSK-A63-HDC32J-120
.91
2.95 4.72 3.54 4.72 6.50 3.54 4.72 6.50 3.54 4.72 6.50 3.54 4.72 6.50 4.72 4.72 4.72 4.72
1.14 2.76 1.54 2.76 4.13 1.57 2.76 4.13 1.57 2.76 4.17 1.57 2.76 4.17
2.09 3.86 2.68 3.86 5.63 2.56 3.74 4.33 2.52 3.70 4.29 2.48 3.66 4.25 3.62 6.58
2.2 2.6 2.2 2.6 3.3 2.4 2.6 3.5 2.4 2.9 3.5 2.4 2.9 3.7 3.3 3.3 4.6 5.1
4mm .787
1.89
.75
1.10
.98
1.89
6mm .787
1.10 1.26 1.06 1.18 1.34 1.14 1.26 1.42 1.22 1.34 1.50
.98
1.97
1.89
8mm .866
1.18
1.97
1
1.89
10mm .945
1.26
1.97
1.89
12mm 1.024
1.38
1.97 1.89 1.89 2.48 2.72
16mm 1.339 20mm 1.496 25mm 2.008 32mm 2.362
1.69
2.99
1.65
2.24
1.97 2.09
1.93 2.20
2
3.66
—
• Coolant pipe must be ordered separately • Adjusting screws cannot be used
ACCESSORIES
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”.
GRIP BAR PG. 415
216
Powered by FlippingBook