BASIC ARBORS
SHRINK FIT HOLDER (SLIM TYPE) CLAMPING RANGE: ø.125" (ø3-8mm)
MAX 90,000 RPM
COOLANT
STAINLESS STEEL ø3-4mm
DIE STEEL ø6-8mm
THROUGH
H
E
L 1
Fig. 1
L
NEW Product
H
H
Coolant Pipe (Optional)
Coolant Pipe (Optional)
E
E
L 1
L 1
Fig. 2
Fig. 3
L
L
Coolant Through
Coolant Through
Catalog Number
Max Insertion Length H
Min Clamping Length E
Weight (lbs.)
Fig.
ød
øD
øD 1
øD 2
L
L 1
HSK-E25-SRM3S-35 HSK-E25-SRM3S-50 HSK-E25-SRM3.175S-35 HSK-E25-SRM3.175S-50 HSK-E25-SRM4S-35 HSK-E25-SRM4S-50 HSK-E25-SRM6S-35 HSK-E32-SRM3S-50 HSK-E32-SRM3S-70 HSK-E32-SRM3.175S-50 HSK-E32-SRM4S-50 HSK-E32-SRM4S-70 HSK-E32-SRM6S-70 HSK-E40-SRM3S-50 HSK-E40-SRM3S-70 HSK-E40-SRM3.175S-50 HSK-E40-SRM4S-50 HSK-E40-SRM4S-70 HSK-E40-SRM6S-50 HSK-E40-SRM6S-70 HSK-E40-SRM8S-60 HSK-E40-SRM8S-80
.31 .37 .31 .38 .35 .41 .43 .33 .41 .33 .37 .45 .53 .33 .41 .33 .37 .45 .44 .53 .52 .61
.71 .77 .72 .78 .75 .69 .71 .73 .81 .74 .77 .85 .93 .73 .81 .74 .77 .85 .85 .93
1.38 1.97 1.38 1.97 1.38 1.97 1.38 1.97 2.76
.67
1.14 1.73 1.14 1.73 1.14 1.73 1.14 1.65 2.44
.1 .1 .1 .1 .1 .1 .1 .3 .3 .3 .3 .4 .4 .5 .5 .5 .5 .5 .5 .5 .6 .6
3mm .236
1.26
.35
.67
.125
.244
1.26
1
.67
4mm .276
.47
1.26
6mm .354
.67 .87
.71
3mm .236
1.65
.35
.125
.244
1.97
.87
1.65
1
4mm .276
.47
2.76
1.65
2.44
6mm .354
.71
1.97 2.76
.87
1.34 2.13
3mm .236
1.65
.35
.125
.244
1.97
.87
1.34
2
4mm .276
.47
2.76 1.97 2.76 2.36 3.15
1.65
2.13 1.22 1.42 1.61 1.93
.87
6mm .354
.71
1.65
1.02 1.02
.87
3
8mm .433
.79
1.65
• Coolant pipe must be ordered separately • Use carbide tool shank with a tolerance of h6 or less • Models marked with an are made of stainless steel • Please note that the rotation speed during use is greatly affected by the balance between the machine rigidity and the tool; when using, start at a low rotation speed and gradually increase it to find the appropriate rotation speed • HSK-E25 and E32 holders cannot be used with coolant through
For models marked corrosion cracking may occur if water-soluble or chlorine-based water-insoluble cutting oil is used with a center-through cutter (including center-through oil mist) due to the material’s properties. Use a non-chlorine-based water-insoluble cutting oil. Please refer to the operation manual of heating/cooling equipment, as some equipment may not be compatible.
258
Powered by FlippingBook