BASIC ARBORS
SHRINK FIT HOLDER CLAMPING RANGE: ø.125" (ø6-12mm)
MAX 90,000 RPM
COOLANT
STAINLESS STEEL ø3-4mm
DIE STEEL ø6-8mm
THROUGH
H
H
E
E
Fig. 1
Fig. 2
L 1
L 1
L
L
NEW Product
H
H
Coolant Pipe (Optional)
Coolant Pipe (Optional)
E
E
L 1
L 1
Fig. 3
Fig. 4
L
L
Coolant Through
Coolant Through
Catalog Number
Max Insertion Length H
Min Clamping Length E
Weight (lbs.)
Fig.
ød
øD
øD 1
øD 2
L
L 1
HSK-E25-SRM3-35
3mm .295
.37 .37 .46 .54 .39 .47 .39 .48 .57 .56 .65 .64 .72 .88 .39 .47 .39 .48 .57 .56 .65 .64 .72 .88
.77 .78 .75 .77 .79 .87 .80 .89 .97 .96
.1 .1 .1 .2 .2 .4 .3 .3 .4 .4 .4 .4 .4 .4 .5 .5 .5 .5 .6 .6 .6 .6 .7 .7
.35
HSK-E25-SRM3.175-35
.125
.303
1
1.38
.67
1.14
HSK-E25-SRM4-35 HSK-E25-SRM6-35 HSK-E32-SRM3-50 HSK-E32-SRM3-70
4mm .394 6mm .472
.47 .71
1.97 2.76
.87
1.65 2.44
3mm .295
1.65
.35
HSK-E32-SRM3.175-50
.125
.303
1.97
.87
1.65
HSK-E32-SRM4-50 HSK-E32-SRM4-70 HSK-E32-SRM6-50 HSK-E32-SRM6-70 HSK-E32-SRM8-50 HSK-E32-SRM10-55 HSK-E32-SRM12-55 HSK-E40-SRM3-50 HSK-E40-SRM3-70
4mm .394
.47
1
2.76 1.97 2.76 1.97
1.65
2.44 1.65 2.44 1.65 1.85 1.77 1.34 2.13
.87
6mm .472
.71
1.65
1.02
8mm .551 10mm .630 12mm .787
.79
.87
2
.94
2.17
.98
.79 .87 .80 .89 .97 .96
1.97 2.76
.87
3mm .295
1.65
.35
HSK-E40-SRM3.175-50
.125
.303
1.97
.87
1.34
HSK-E40-SRM4-50 HSK-E40-SRM4-70 HSK-E40-SRM6-50 HSK-E40-SRM6-70 HSK-E40-SRM8-60 HSK-E40-SRM10-65 HSK-E40-SRM12-65
3
4mm .394
.47
2.76 1.97 2.76 2.36
1.65
2.13 1.22 1.42 1.61
.87
6mm .472
.71
1.05
1.65
8mm .551 10mm .630 12mm .787
.79
4
1.02
.87
2.56
1.81
.98
• Coolant pipe must be ordered separately • Use carbide tool shank with a tolerance of h6 or less • Models marked with an are made of stainless steel • Please note that the rotation speed during use is greatly affected by the balance between the machine rigidity and the tool; when using, start at a low rotation speed and gradually increase it to find the appropriate rotation speed • HSK-E25 and E32 holders cannot be used with coolant through
For models marked corrosion cracking may occur if water-soluble or chlorine-based water-insoluble cutting oil is used with a center-through cutter (including center-through oil mist) due to the material’s properties. Use a non-chlorine-based water-insoluble cutting oil. Please refer to the operation manual of heating/cooling equipment, as some equipment may not be compatible.
259
Powered by FlippingBook