HYDRAULIC CHUCKS
HYDRAULIC CHUCK CLAMPING RANGE: ø14-32mm For Drills, Reamers, Ball Mills, End Mills, Diamond Reamers & Grinding Tools
COOLANT
THROUGH
Adjusting Screw (Optional)
H
E
L 1
L
Catalog Number
Min Clamping Length E
Adjusting Screw
Weight (lbs.)
ød
øD
øD 1
L
L 1
H
C5-HDC14-90 C5-HDC16-75 C5-HDC16-90 C5-HDC18-90 C5-HDC20-75 C5-HDC20-90 C5-HDC25-90 C6-HDC14-90 C6-HDC14-120 C6-HDC16-75 C6-HDC16-90 C6-HDC16-120 C6-HDC18-90 C6-HDC18-120 C6-HDC20-75 C6-HDC20-90 C6-HDC20-120 C6-HDC25-90 C6-HDC25-120 C6-HDC32-90 C6-HDC32-120
14mm 1.339
1.772 1.969 1.890 1.890 2.047 1.969 2.480
3.58 2.95 3.54 3.54 2.95 3.54 3.54 3.54 4.72 2.95 3.54 4.72 3.54 4.72 2.95 3.54 4.72 3.54 4.72 3.54
1.89 1.38 1.89 1.89 1.38 1.89 1.89
1.50 2.68 3.27 1.69 2.68 3.27 3.27
2.09-2.36
2.4 2.4 2.7 2.7 2.4 2.7 3.8 3.5 4.2 3.5 3.8 4.4 3.7 4.4 3.8 4.0 4.6 4.9 6.2 6.2 6.6
HDA12-10010 z
— — — — — —
16mm 1.496
1.69
18mm 1.575
3.27
20mm 1.654
1.69
25mm 2.165
2.05
1.89-2.36 1.50-2.36
HDA10-08015 HDA10-08032
14mm 1.339
1.772
1.89
1.50
1.969 1.850 1.890 1.890 1.929 2.087
1.38
2.60 3.19
—
16mm 1.496
1.69
1.89
1.69-2.76
HDA16-12037
2.60
—
18mm 1.575
1.89
1.69
1.69-2.76
HDA16-12037
1.30
2.60 2.83
—
20mm 1.654
1.69
1.969
1.89
1.69-2.76
HDA16-12037
1.81 2.01 1.69
3.15
—
25mm 2.165
2.480
2.05
2.64-3.11
HDA20-16015
2.953 2.480
2.480
3.19
—
32mm
2.20
— 4.72
— 2.60-3.07
HDA20-160315
• “H” indicates the adjustment length with an adjusting screw • Do not attempt to balance before first consulting BIG DAISHOWA • In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides (ex: HDA6-05020W) • The above type is not available for HDA12-10010 with models marked z • Adjusting screws cannot be used with models marked
ACCESSORIES
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”.
PERFECT SEAL/ JET COLLET PG. 404
GRIP BAR PG. 415
SCREW PG. 415
284
Powered by FlippingBook