HYDRAULIC CHUCKS
Catalog Number
Min Clamping Length E
Max RPM
Weight (lbs.)
ØD 2
L
L 1
L 2
Fig.
Ød
ØD
ØD 1
2.9 3.1 2.6 2.9 3.1 2.9 2.9 3.5 3.7 3.1 3.8 4.0 3.1 3.8 4.2 3.1 4.0 4.4 9.3
BBT40-HDC3S-90 BBT40-HDC3S-135 BBT40-HDC4S-60 BBT40-HDC4S-90 BBT40-HDC4S-135 BBT40-HDC5S-90 BBT40-HDC6S-110 BBT40-HDC6S-150 BBT40-HDC6S-180 BBT40-HDC8S-110 BBT40-HDC8S-150 BBT40-HDC8S-180 BBT40-HDC10S-110 BBT40-HDC10S-150 BBT40-HDC10S-180 BBT40-HDC12S-110 BBT40-HDC12S-150 BBT40-HDC12S-180 BBT50-HDC4S-150 BBT50-HDC4S-200 BBT50-HDC6S-150 BBT50-HDC6S-200 BBT50-HDC8S-150 BBT50-HDC8S-200 BBT50-HDC10S-150 BBT50-HDC10S-200 BBT50-HDC12S-150 BBT50-HDC12S-200
1.50 1.73
.94
3.54 5.31 2.36 3.54 5.31 3.54 4.33 5.91 7.09 4.33 5.91 7.09 4.33 5.91 7.09 4.33 5.91 7.09 5.91 7.87 5.91 7.87 5.91 7.87 5.91 7.87 5.91 7.87
1.73 2.24
— 84 —
35,000 30,000 30,000 30,000 30,000 30,000 30,000 28,000 25,000 30,000 28,000 25,000 30,000 25,000 23,000 30,000 25,000 23,000 20,000 15,000 20,000 15,000 20,000 15,000 20,000 15,000 20,000 15,000
3mm
1
.551
.63
1.02
.75 .94
.87
1
4mm
.551
1.50
1.77 2.24 1.81 2.36
3.31 3.31
.75
2 1 1
1.02
5mm
.551
1.50 1.50
.94
— —
.83
1.06
6mm
.551
3.35 3.94
.98
2
1.89
1.02
2.24
1.57
1.18
2.36
—
1
8mm
.669
3.35 3.94
1.18
2
1.97
1.10
2.05
1.65
1.26
2.36
—
1
10mm
.748
3.35 3.94
1.26
2
1.97
1.18
2.05
1.73
1.34
2.36
—
1
12mm
.827
3.35 3.94 3.27 3.94 3.27 3.94 3.27 3.94 3.27 3.94 3.27 3.94
1.38
2
1.97
1.26
2.05
2.05 2.20 2.05 2.20 2.12 2.28 2.20 2.36 2.28 2.44
4mm
.551
1.02
2.24
.75
10.1
9.3
6mm
.551
1.02
.98
10.1
2.24
9.5
8mm
.669
1.10
1.18
2
10.4
9.5
10mm
.748
1.18
1.26
10.6
2.05
9.7
12mm
.827
1.26
1.38
10.6
• Adjusting screw cannot be used • Some coolant may leak from the inner diameter slits when center through coolant is used with models marked
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
GRIP BAR PG. 407
135
Powered by FlippingBook