Catalog Number
Weight (lbs.)
Fig.
Ød
ØD
ØD 1
ØD 2
L
L 1
E
BBT40-HDC4J-90 BBT40-HDC4J-135 BBT40-HDC6J-90 BBT40-HDC6J-135 BBT40-HDC6J-165 BBT40-HDC8J-90 BBT40-HDC8J-135 BBT40-HDC8J-165 BBT40-HDC10J-90 BBT40-HDC10J-135 BBT40-HDC10J-165 BBT40-HDC12J-90 BBT40-HDC12J-135 BBT40-HDC12J-165 BBT40-HDC16J-90 BBT40-HDC16J-135 BBT40-HDC20J-90 BBT40-HDC20J-135 BBT40-HDC25J-90 BBT40-HDC32J-90 BBT50-HDC4J-120 BBT50-HDC6J-120 BBT50-HDC8J-120 BBT50-HDC10J-120 BBT50-HDC12J-120 BBT50-HDC16J-120 BBT50-HDC20J-120 BBT50-HDC25J-120 BBT50-HDC32J-120
1.50 1.73 1.50 1.73 1.81 1.57 1.81 1.89 1.65 1.89 1.97 1.73 1.97 2.05 1.81 1.97 1.89 2.09 2.48 2.95 1.89 1.89 1.97 2.05 2.13 2.28 2.44 2.76 3.07
.98
3.54 5.31 3.54 5.31 6.50 3.54 5.31 6.50 3.54 5.31 6.50 3.54 5.31 6.50 3.54 5.31 3.54 5.31
1.77 3.35 1.77 3.35 4.13 1.77 3.35 4.13 1.77 3.35 4.13 1.77 3.35 4.13 1.81 3.50 1.85 3.54 1.61
2.9 3.3 2.9 3.3 3.7 2.9 3.5 4.0 2.9 3.5 4.2 2.9 3.7 4.4 3.1 4.2 3.3 4.4 4.2 5.1 8.8 9.0 9.0 9.3 9.3 9.7 9.9
4mm
.787
.75
1.18
.98
6mm
.787
1.14 1.26 1.06 1.22 1.34 1.14 1.30 1.42 1.22 1.38 1.50 1.57 1.73 1.73 1.89 2.20
.98
8mm
.866
1.18
10mm
.945
1.26
1
12mm
1.024
1.38
16mm
1.339
1.65
20mm
1.496
1.65
25mm 32mm
2.008 2.322
1.93 2.20
3.54
—
.79
2
4mm 6mm 8mm
.787 .787 .866 .945
1.02 1.02 1.10 1.18 1.26 1.61 1.77 2.28 2.64
.75 .98
2.17
1.22 1.30 1.42
10mm 12mm 16mm 20mm 25mm 32mm
4.72
1.024 1.339 1.496 1.890 2.283
1
2.20
1.69
2.32 2.36
1.93 2.20
11.5 12.3
• Adjusting screws cannot be used
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
GRIP BAR PG. 407
143
Powered by FlippingBook