HYDRAULIC CHUCKS
JET COOLANT TYPE CLAMPING RANGE: Ø4-32mm Coolant Holes Through Body of Holder
COOLANT
JET THROUGH
THROUGH
H
H
Coolant Pipe (Optional)
Coolant Pipe (Optional)
Min Clamping Length E
Min Clamping Length E
Manual Clamping Hole
Manual Clamping Hole
L 1
L 1
L
L
Fig. 1
Fig. 2
Weight (lbs.)
Catalog Number
ØD 2
L
L 1
H
E
Fig.
Ød
ØD
ØD 1
HSK-A63-HDC4J-75 HSK-A63-HDC4J-120 HSK-A63-HDC6J- 90 HSK-A63-HDC6J-120 HSK-A63-HDC6J-165 HSK-A63-HDC8J- 90 HSK-A63-HDC8J-120 HSK-A63-HDC8J-165 HSK-A63-HDC10J- 90 HSK-A63-HDC10J-120 HSK-A63-HDC10J-165 HSK-A63-HDC12J- 90 HSK-A63-HDC12J-120 HSK-A63-HDC12J-165 HSK-A63-HDC16J-120 HSK-A63-HDC20J-120 HSK-A63-HDC25J-120 HSK-A63-HDC32J-120
.91
2.95 4.72 3.54 4.72 6.50 3.54 4.72 6.50 3.54 4.72 6.50 3.54 4.72 6.50 4.72 4.72 4.72 4.72
1.14 2.76 1.54 2.76 4.13 1.57 2.76 4.13 1.57 2.76 4.17 1.57 2.76 4.17
2.09 3.86 2.68 3.86 5.63 2.56 3.74 4.33 2.52 3.70 4.29 2.48 3.66 4.25 3.62 6.58
2.2 2.6 2.2 2.6 3.3 2.4 2.6 3.5 2.4 2.9 3.5 2.4 2.9 3.7 3.3 3.3 4.6 5.1
4mm
.787
1.89
.75
1.10
.98
1.89
6mm
.787
1.10 1.26 1.06 1.18 1.34 1.14 1.26 1.42 1.22 1.34 1.50
.98
1.97
1.89
8mm
.866
1.18
1.97
1
1.89
10mm
.945
1.26
1.97
1.89
12mm
1.024
1.38
1.97 1.89 1.89 2.48 2.72
16mm 20mm 25mm 32mm
1.339 1.496 2.008 2.362
1.69
2.99
1.65
2.24
1.97 2.09
1.93 2.20
3.66
2
—
• Coolant pipe must be ordered separately • Adjusting screws cannot be used
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
GRIP BAR PG. 407
202
Powered by FlippingBook