COLLET CHUCKS
MEGA NEW BABY CHUCK CLAMPING RANGE: Ø.010"-.787" (Ø.25-20mm) For Drills, Reamers, Taps & Finishing End Mills
COOLANT
MAX 35,000 RPM
THROUGH
L
L 1
H
Adjusting Screw (Optional)
Catalog Number
Max RPM
Weight (lbs.)
Ød
ØD
L
L 1
H
Collet
Nut
Wrench
HSK-F63-MEGA6N-75 HSK-F63-MEGA6N-90 HSK-F63-MEGA6N-105 HSK-F63-MEGA6N-135 HSK-F63-MEGA8N-75 HSK-F63-MEGA8N-90 HSK-F63-MEGA8N-105 HSK-F63-MEGA8N-120 HSK-F63-MEGA8N-135 HSK-F63-MEGA8N-165 HSK-F63-MEGA10N-75 HSK-F63-MEGA10N-90 HSK-F63-MEGA10N-105 HSK-F63-MEGA10N-120 HSK-F63-MEGA13N-75 HSK-F63-MEGA13N-90 HSK-F63-MEGA13N-105 HSK-F63-MEGA13N-120 HSK-F63-MEGA13N-165 HSK-F63-MEGA16N-75 HSK-F63-MEGA16N-90 HSK-F63-MEGA16N-105 HSK-F63-MEGA20N-75 HSK-F63-MEGA20N-90 HSK-F63-MEGA20N-105
2.95 3.54 4.13 5.31 2.95 3.54 4.13 4.72 5.31 6.50 2.95 3.54 4.13 4.72 2.95 3.54 4.13 4.72 6.50 2.95 3.54 4.13 2.95 3.54 4.13
1.65 2.09 2.72 3.90 1.69 2.13 2.72 3.31 3.90 5.08 1.69 2.13 2.72 3.31 1.69 2.20 2.80 3.39 5.16 1.69 2.28 2.87 1.77 2.36 2.95
.91-1.22
35,000 30,000 25,000 20,000 32,000
1.5 1.8 1.8 2.0 1.8 2.0 2.0 2.0 2.2 2.4 2.0 2.0 2.2 2.4 2.0 2.2 2.4 2.6 3.5 2.2 2.6 2.9 2.4 2.9 3.1
.010-.236
.787
MGN6
MGR20
NBC6-
.91-1.69
1.02-1.50
30,000
.020-.315
.984
MGN8
MGR25
NBC8-
1.02-1.77
25,000 20,000 15,000 32,000 30,000
1.89
.059-.354
1.181
MGN10
MGR30
NBC10-
1.50-1.89
25,000
1.85 2.40
30,000
.098-.512
1.378
1.73-2.09
MGN13
MGR35
25,000 20,000 15,000 30,000 25,000 20,000 30,000 25,000 20,000
NBC13-
1.73-2.48
1.89 2.40
.098-.630
MGN16
MGR42
1.654
NBC16-
1.89-2.20
2.01 2.40
.098-.787
1.811
MGN20
MGR46
NBC20-
2.01-2.28
• MEGA NEW BABY NUT is included; coolant pipe, collet, wrench and adjusting screw must be ordered separately • Please note that the practical spindle speed may be considerably influenced by the machine rigidity and tool balance, when using, slowly ramp up to the appropriate speed starting from slow speeds • “H” indicates the adjustment length with an adjusting screw • Contact us for a plug screw to block a coolant through hole • Adjusting screws cannot be used with models marked • If HSK tool holders are used in a machine which does not recommend the center through coolant, the plug screw should be mounted to our tools
ACCESSORIES
COLLET PG. 372
MEGA NUT PG. 378
PERFECT SEAL PG. 380
MEGA WRENCH PG. 402
SCREW PG. 423
240
Powered by FlippingBook