HYDRAULIC CHUCKS
HYDRAULIC CHUCK LATHE TYPE — F TYPE CLAMPING RANGE: Ø.118"-.250" (Ø3-12mm) Single wrench enables easy cutting tool change on the tool post. User-friendly rear clamping design is ideal for front tool post.
H
H
Rc(PT)1/8
E
E
L 1
L 1
W A
L
L
Fig. 1
Fig. 2
Weight (lbs)
Catalog Number
A
B
W H
E
Fig.
Ød
ØD
ØDS
L
L 1
.118 .157 .236 .315 .125 .188 .250
SL19.05F-HDC3-85 SL19.05F-HDC4-85 SL19.05F-HDC6-80 SL19.05F-HDC8-80
.63 .75 .98
.551
3.35
.20
2.99
.46
.44 .42
—
3.15
—
2.80
1
.750
.67
.55
.87
1.22
SL19.05F-HDC3.175-85 SL19.05F-HDC4.7625-85 SL19.05F-HDC6.35-80
.63 .86 .98 .63 .75
.551
3.35
.20
2.99
.53
—
3.15
—
2.80
.49
3mm 4mm 6mm 8mm 3mm 4mm 6mm 8mm
SL20F-HDC3-75 SL20F-HDC4-75 SL20F-HDC6-70 SL20F-HDC8-70 SL22F-HDC3-75 SL22F-HDC4-75 SL22F-HDC6-70 SL22F-HDC8-70 SL22F-HDC10-70 SL25F-HDC3-110 SL25F-HDC4-110 SL25F-HDC6-105 SL25F-HDC8-100 SL25F-HDC10-95 SL25F-HDC12-90 SL25.4F-HDC3-105 SL25.4F-HDC4-105 SL25.4F-HDC6-100 SL25.4F-HDC8-95 SL25.4F-HDC10-90 SL25.4F-HDC12-85
.551
2.95
.20
2.60
.49
20mm
.67
.53
.91
1
1.00 1.22
.44 .42
—
2.76
—
2.40
.63 .75
.551
2.95
.20
2.60
.57
22mm
.67
.53
.98
1
1.00 1.22 1.30
.53 .51 .50
—
2.76
—
2.40
10mm
3mm 4mm 6mm 8mm
.63 .75 .98
4.33
.28
3.23
.82
.551
4.13 3.94 3.74 3.54
3.03 2.83 2.64 2.40
.75 .68 .62 .53
2
25mm
— — —
.12
.669
1.22 1.30 1.42
10mm 12mm
—
—
3mm 4mm 6mm 8mm
.63 .75 .98
1.13
.28
3.03
.79
.511
3.94 3.74 3.54 3.35
2.83 2.64 2.44 2.20
.75 .66 .60 .53
1.000
— — —
.12
2
.669
1.22 1.30 1.42
10mm 12mm
—
—
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
• Adjusting screw cannot be used • “E” is the min. clamping length • “H” indicates the adjustment length with an adjusting screw • Some coolant may leak from the inner diameter slits when center through coolant is used with models marked F Type • Tighten from the opposite side of the tool • Coolant delivery is possible with Rc(PT)1/8 screw • Optimum overall length for easy use • Ideal for use on a front tool post
ACCESSORIES
GRIP BAR PG. 407
320
Powered by FlippingBook