HYDRAULIC CHUCKS
CLAMPING RANGE: Ø.250"-1.250" (Ø6-20mm) For Drills, Reamers, Ball Mills, End Mills, Diamond Reamers & Grinding Tools
COOLANT
R
SPINDLE SYSTEM DUAL CONTACT
THROUGH
H
H
Adjusting Screw (Optional)
Adjusting Screw (Optional)
Adjusting Screw (Optional)
H
E
E
E
L 1
L 1
Fig. 3
Fig. 1
Fig. 2
L 1
L
L 2
L
L
Catalog Number
Min Clamping Length E
Adjusting Screw
Weight (lbs.)
Fig.
Ød
ØD ØD 1
ØD 2
L
L 1
L 2
H
BCV40-HDC.250-2.5 BCV40-HDC.250-4 BCV40-HDC.250-5.5 BCV40-HDC.375-2.5 BCV40-HDC.375-4 BCV40-HDC.375-5.5 BCV40-HDC.500-2.5 BCV40-HDC.500-4 BCV40-HDC.500-5.5 BCV40-HDC.625-3 BCV40-HDC.625-4 BCV40-HDC.625-5.5 BCV40-HDC.750-3 BCV40-HDC.750-4 BCV40-HDC.750-5.5 BCV40-HDC1.000-3 BCV40-HDC1.000-4 BCV40-HDC1.000-5 BCV40-HDC1.250-4 BCV40-HDC6-90 BCV40-HDC8-90 BCV40-HDC10-90 BCV40-HDC12-90 BCV40-HDC20-90
1
— 2.50
1.02
—
2.4 3.1 3.8 2.7 3.1 4.0 2.7 3.3 4.0 2.9 3.3 4.2 3.1 3.6 4.4 4.0 4.7 5.8 5.8
1.20 1.75
4.00 5.50
2.48 4.09
.250
1.024 1.750
1.10-1.97
1.10
HDA6-05032
2
1.75
1
— 2.50
1.04
—
.375
1.181 1.750
1.37 1.75
4.00 5.50
2.52 4.09
1.30-2.17
1.30
HDA10-08032
2
1.75
1
— 2.50
.98
—
.500
1.299 1.750
1.75
4.00
2.60 4.09
1.50-2.36
1.50
HDA12-10032
2
1.75
— 5.50
1
3.00 4.00 5.50
1.54
—
HDA16-12030
.625
1.496 1.750 1.75
2.60
1.69-2.76
1.69
2
2.00
HDA16-12037
—
1
— 3.00
1.57
2.60 4.09 4.13
HDA16-12030
.750
1.654 1.750
4.00 5.50 3.00 4.00 5.00
1.69-2.76
1.69
2
1.75
2.00
HDA16-12037
.61
HDA16-12015
1.000
3
2.165 2.480
—
1.25 1.75 1.25 1.89 1.72 1.75 1.76 1.58
— 2.05-3.15
2.05
HDA25-16039
1.250 6mm 8mm 10mm 12mm 20mm
3
2.677 2.953
— 4.00
— 2.20-3.15
2.20
HDA25-16039 HDA6-05032 HDA8-06032 HDA10-08032 HDA12-10032 HDA16-12037
1.024 1.102 1.181 1.260
1.10-1.97
1.10
2.8
1
1.750
— 3.54
—
1.30-2.17 1.50-2.36
1.30 1.50 1.69
2.9
1.653 1.750
— 3.54
— 1.69-2.76
4.4
2
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
• Adjustable cutter length H is the adjustable length in the use of adjusting screw
ACCESSORIES
PERFECT SEAL/ JET COLLET PG. 395
GRIP BAR PG. 407
SCREW PG. 407
77
Powered by FlippingBook