HYDRAULIC CHUCKS
HYDRAULIC CHUCK LATHE TYPE — STANDARD TYPE CLAMPING RANGE: Ø.125"-.250" (Ø3-12mm) High-precision cutting with hydraulic chuck is achieved on an automatic lathe.
COOLANT
H
THROUGH
E
G
Rc(PT)1/8
L 1
A
L
W
Catalog Number
Ød
ØDs
L
L 1
A
B 1
B 2
W
H
E
G
3mm
SL19.05-HDC3-60
.787-1.26
.63
.125
SL19.05-HDC3.175-60
HDA4-05015W
SL19.05-HDC4-60
4mm .1875 5mm 6mm
.905-1.26
.75
SL19.05-HDC4.7625-60 SL19.05-HDC5-60 SL19.05-HDC6-60 SL19.05-HDC6.35-60 SL19.05-HDC8-60 SL20-HDC3-70 SL20-HDC4-70 SL20-HDC5-70 SL20-HDC6-70 SL20-HDC8-70 SL22-HDC3-70 SL22-HDC4-70 SL22-HDC6-70 SL22-HDC8-70 SL22-HDC10-70 SL25-HDC3-65 SL25-HDC4-65 SL25-HDC6-65 SL25-HDC8-65 SL25-HDC10-65 SL25-HDC12-65 SL25.4-HDC3-80 SL25.4-HDC4-80 SL25.4-HDC6-80 SL25.4-HDC8-80 SL25.4-HDC10-80 SL25.4-HDC12-80
.91
.750
2.36
.787
.59
.62
.87
.87
1.22-1.89
NBA6B
.98
.250
8mm 3mm 4mm 5mm 6mm 8mm 3mm 4mm 6mm 8mm
.95
2.56
1.22
—
.787-1.26 .905-1.26
.63 .75 .87 .98
HDA4-05015W
.91
20mm 2.75
1.18
.59
.62
.90
1.22-1.89
NBA6B
.95
2.95
1.22
—
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
HDA4-05015W
.91
.62
22mm 2.75
1.18
.59
.98
NBA6B
.95
2.95 2.76
1.22 1.30
—
10mm
1.06
.66
3mm 4mm 6mm 8mm
.63 .75 .98
.787-1.26 .905-1.26 1.22-1.89
HDA4-05015W
.91
.55
.91 .95
.59 .63 .67 .71
NBA6B
25mm 2.56
1.57
.59
1.10
2.76
1.22 1.30 1.42
—
10mm 12mm
1.06 1.10
2.56
3mm 4mm 6mm 8mm
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
.91
.55
HDA4-05015W
.91 .95
.59 .63 .67 .71
NBA6B
1.000
3.15
1.57
.59
1.10
3.35
1.22 1.30 1.42
—
10mm 12mm
1.06 1.10
3.15
ACCESSORIES
• Adjusting screws cannot be used with models marked • Adjusting screw is adjustable both from the head and shank ends • “E” is the min. clamping length • “G” is the adjusting screw (optional) • “H” indicates the adjustment length with an adjusting screw • “H” at HDC8/10/12 is the max. tool shank length can be inserted for these models • L 1 is the minimum length, in case of shortening the shank • Some coolant may leak from the inner diameter slits when center through coolant is used with models marked
PERFECT SEAL/ JET COLLET PG. 395
GRIP BAR PG. 407
SCREW PG. 407
Use only cutting tools that have a shank tolerance of h6 (see table pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with hydraulic chucks. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
319
Powered by FlippingBook